Bosch Vr8 Installation Manual English. BOSCH 16B Installation Manual BOSCH 10B Users Guide BOSCH 16B Users Guide BOSCH. Bosch Vr8 Installation Manual -}. VR8 User Guide Notice VR8 User Guide. Bosch Security Systems Pty Ltd reserves the right to make changes to features and. INstallatioN maNual - Wireless. Command 958 - Exit from Installer's Programming Mode without saving. Refer to the installation and operation manuals for the B810 wireless receiver.

• Installation Guide
• Bosch Vr8 Installation Manual English

• Carmel Cole
• 3 years ago
• Views:

Transcription

1 NetworX NX- Control/Communicator Installation Manual Table of Contents General Description.. Ordering Information.. Feature Definitions.. - Programming the LED Keypads.. Programming the NX Types of Programming Data Enrolling the Modules & Keypads.. L Quick Start Installations.. Communicator Formats.. Reporting Events to Phone #, #, & #.. - Default Zone Types.. Zone Doubling.. Programming the Outputs.. - Programming Worksheets SIA and Contact ID Formats.. - Expander Trouble Reporting Information.. Wiring Diagram.. Terminal Description.. Telephone Interface Information.. CE Notice / Declaration.. Underwriters Laboratories Information.. Specifications.. Back GE Interlogix Gladewater, Texas

2 GENERAL DESCRIPTION The NetworX NX- represents a new approach to security systems design. Drawing on our experience in the world market as the largest exporter of USA manufactured controls, we have developed the most flexible, durable, and userfriendly control ever seen in our industry. Featuring sophisticated software which allows up to 99 users to interface with zones, partitions, and a host of integrated fire, access, verification, and input/output modules, all reported with the most comprehensive and fast SIA and Contact ID formats. The NetworX design allows a fully loaded system to be housed in one single metal enclosure, establishing for the first time, a logical solution and design response to modular systems. Up to modules can be added to expand the capabilities of the NX-. ORDERING INFORMATION CADDX PART # DESCRIPTION NX- KIT Includes NX- Control, NX-0E LED Keypad, &.V VA Transformer NX- NX- Control Only NX-0E Zone LED Keypad NX-E Zone LED Keypad NX-E Zone LED Keypad NX-E Alphanumeric LCD Keypad NX-00 ** Zone Doubling Kit (Includes 00.k and 00.9k resistors) NX- Zone Expander Module NX-0 ** Smart Power Supply and Buss Extender NX-0E # Zone Wireless Expansion Module (UL LISTED PART #0-90) NX-E # Zone Wireless Expansion Module (UL LISTED PART #0-90) NX-E # Zone Wireless Expansion Module (UL LISTED PART #0-90) NX-0E Seven Relay Module NX-0E Eight Output Module NX-E ** Two-Way Listen-In Module NX-0E ** 'Operator' Telephone Interface Module NX-0E ** Cellemetry Interface NX-0E ** Fire Supervision Module NX-9E 9 Zone LCD Keypad NX-0E Zone LED Keypad NX-E Zone LCD Keypad NX-0E Zone LED Door Design Keypad NX-E Zone LED Door Design Keypad NX-E Zone LED Door Design Keypad NX-E Zone Fixed Language Icon Keypad ** These products have not been tested and approved by Underwriters Laboratories, Inc. # These wireless devices are only UL listed for residential applications. Page

3 FEATURE DEFINITIONS Abort - If enabled, the NX- will wait the programmed number of seconds in location 0 prior to sending an alarm. During this delay time, the 'Cancel' LED will flash. To abort the report, type in a code and press the [Cancel] key. The LED will extinguish. If the report is not aborted within the allotted time, the LED will extinguish when the report is sent. ADialer must be enabled in the ACharacteristic of locations 0-9. (See locations 0 and 0-9, pages and ) AC Fail / Low Battery Report/Warning- The NX- can be programmed to report AC failure and/or Low Battery conditions to the central station. It can also be programmed to sound the keypad immediately upon detection of the condition. The AC failure report/warning can be delayed.(see locations and 9, page ) AC Power / Low Battery Sounder Alert- If enabled, the NX- will beep the keypad sounder upon arming or disarming if the AC power is missing or a low battery has been detected. (See location, page ) Arm / Disarm Codes - The NX- can have 99 four-digit codes or six-digit codes to arm/disarm the control. All codes must have the same number of digits. The factory default for User # is []-[]-[]-[] when using a -digit code, or []-[]-[]-[]-[]-[] for a -digit code. This code can then be used to enter the new arm/disarm codes. (See location, page ) Automatic Arming - If programmed, the NX- will Auto Arm at a specified time. At this time, the keypad will beep for 0 seconds before the panel arms. The arming process will be stopped if a code is entered on the keypad. The NX- will attempt to arm after every minutes of inactivity until the next opening time (loc. ), or until the system is armed. The -minute timer will be extended when there is activity in the building causing the 'Ready' LED to turn off and on. If closing reports are sent, the user code will be 9. (See locations, and -, pages and ) NOTE: For UL installations, this feature shall be disabled. Auto Cancel / Abort - If enabled, the Cancel and/or Abort features will be automatic (pressing the [Cancel] button is not required). The Cancel and Abort features, in locations and 0 respectively, must be enabled to permit this Auto feature to work. For proper operation of these features, ADialer must be enabled in the ACharacteristic of locations 0-9 Zone Types. (See location, page ) Automatic Bypass / Instant Arming - When enabled, the control panel can automatically bypass interior follower zones if an exit is not detected during the exit delay time. Entry delay zones can also be made instant. (See location, segments and, page ) Auto Test- This feature will cause the panel to call the central station to report a communicator test at a specified interval. (See location, page ) Auxiliary Outputs- The NX- has four programmable outputs that can be used to activate relays, LED=s, etc. (See the terminal description on page and locations -0, pages -) Auxiliary Power Overcurrent- The NX- will illuminate the 'Service' LED on the keypad whenever too much current is drawn from any device powered by the system. This condition can be reported to the central station. (See location, page ) Box Tamper- The NX- has an input for a normally closed tamper switch (see terminal drawing). The Box Tamper can be programmed to report and/or sound the siren and/or the keypad. These terminals can be enabled or disabled in programming. (See locations and 9, page ) Built In Siren Driver - The NX- has a built-in db siren driver. When desired, this built-in driver can be easily convertedtoaampvoltageoutputthrough programming. (See location, page ) Bypass Toggle- This feature will enable the end user to toggle (turn on or off) the bypass of an interior zone with the system armed by pressing the [Bypass] key. (See location, page ) Call Back- When enabled, the control will use the call back phone number to call the download computer before beginning a download. (See location, page ) Page

4 Cancel - If enabled, the NX- will send a 'Cancel' report if when the system is disarmed and the [Cancel] button is pressed within minutes of an alarm. Once the [Cancel] key is pressed, the 'Cancel' LED will illuminate until the central station acknowledges the 'Cancel' report. ADialer must be enabled in the ACharacteristic of locations 0-9. (See location, page ) Code Required Options- The NX- can be programmed to require a code for bypassing zones and/or initiating a download using the [r]-[9]-[] or[r]-[9]-[9] function. (See locations and, pages and ) Communication Formats- The NX- can report in multiple formats. It is recommended that you use Contact ID or SIA formats if possible. If you wish to report to a pager or in a + format to a central station, you must program each code to be reported. (See locations - and -9, pages -0 and -) Cross Zoning - This feature requires two or more trips on a zone or zones programmed as 'cross zones' within a specified time before reporting an alarm. During the time between trips, the NX- can be programmed to sound the keypad and/or the siren. The NX- can also be programmed to report an alarm after two or more trips on the same zone. (See locations, 9, 0 and 0-9, pages -, - ) Dual / Split / Multiple Reports - The NX- can send communication reports to three different phone numbers for dual, split or multiple reports selectable by event or partition. (See locations, 0, and, pages -) Duress Code- If a duress code is programmed the NX- will send a duress signal whenever the panel is armed or disarmed with this code. If open/close reports are sent, the user code will be. (See location, page ) Dynamic Battery Test - The NX- can be programmed to perform a Dynamic Battery Test for a selected duration the first time the panel is armed or disarmed every day, as well as by pressing [r][] Test Function. If the panel is not armed or disarmed during the day, it will perform the test at midnight. The NX- can also be programmed to perform a missing battery test every seconds. (See locations and 0, pages and ) Entry-Guard - This unique low level arming mode has been developed to reduce the most common source of false alarms. When armed with the LED on, the opening of any zones designated as 'Entry Guard zone' will initiate the keypad sounder and start the entry delay before creating an alarm. All other zones will function as normal. This arming mode will encourage system owners to use their system more frequently when the premises are occupied. (See locations -9, pages -) NOTE: For UL installations, this feature shall be disabled. Exit Error - If enabled, the NX- will send an 'Exit Error Report' if an entry/exit zone is faulted at the instant the exit delay expires. This report will be sent along with the user number that armed the system, if the panel is not disarmed before the entry delay expires. The alarm report will also be sent. Even if this feature is not enabled, the siren will sound if any entry/exit zone is faulted at the instant the exit delay expires. (See location, page ) Expander Trouble- The NX- will report expander trouble to the central station if enabled. This condition will illuminate the 'Service' LED on the keypad even if not reported. NOTE: The keypads are considered expanders. The number of the expansion devices reported can be found on page. (See location, page ) Fail to Communicate- The NX- will illuminate the 'Service' LED if a report fails to reach the central station. If enabled, when the next report is successfully communicated, a Fail to Communicate code will be reported. (See location, page ) Fire Alarm Verification - When enabled, the NX- will verify a Fire alarm by requiring more than one trip on a smoke detector within a specified time before creating an alarm. (See location 0, page ) This feature is not approved for residential use in California. Force Arming - When enabled, the NX- can be Force Armed with zones violated. Under this condition, if a force armable zone is not secure, the 'Ready' LED will flash. At the end of the exit delay, these zones will become bypassed. If these zones become secured any time during the arming cycle, they will be unbypassed and active in the system. If 'Bypass Report' is enabled, the force arming zones can be programmed to report bypass when they are Force Armed (default), or to not report bypass even if 'Bypass Report' is enabled. (See locations, and -9, pages & -) NOTE: For UL installations, this feature shall be disabled. Ground Fault- If the NX-0 is used, a fault of the earth ground can be reported to the central station. If it is not reported, this condition will illuminate the 'Service' LED on the keypad. (See location, page ) Page

5 Group Bypass - A designated group of zones can be programmed to bypass by pressing [Bypass]- [0]-[Bypass]- [Bypass] prior to arming. (See locations -9, pages -) NOTE: For UL installations, this feature shall be disabled. Immediate Restore By Zone- The NX- can be programmed to send alarm and restore reports as soon as they occur, or wait until the siren time has expired. (See location, page ) Internal Event Log - Up to events can be stored in memory along with the date and time of the event. These events can later be viewed through downloading. All reportable events report to the log. Keypad Activated Panics- The NX- has three keypad activated panics that will send reports to the central station: Auxiliary (Fire), Auxiliary (Medical), and Keypad Panic. Auxiliary will activate the steady (Fire) siren, Auxiliary will sound the keypad, and the Keypad Panic can be programmed to be silent or audible (sound siren). (See location, page ) Keypad Sounder Control- The NX- can be programmed to sound the keypad sounder for certain events. (See location 9, page ) Keypad Tamper- If enabled, the NX- will disable the keypad for 0 seconds and communicate a tamper signal to the central station if 0 keypresses are entered without producing a valid code. (See location, page ) Keyswitch Arm/Disarm - Any zone on the NX- can be programmed as a keyswitch zone. If this is done, a momentary short on this zone will arm/disarm the control. If opening/closing reports are sent, the user code will be 99. (See 'Default Zone Types', page ) LED Extinguish- This feature will extinguish all LED=s on the keypad, except the 'Power' LED, after 0 seconds without a keypress. Pressing any numeric key will illuminate all LED=s. (See location, page ) Local Programming Lockout- This feature will disable programming of all locations or specified locations from the keypad. (See location, page ) Log Full Report- A report can be sent to the central station when the event log is full. (See location, page ) Lost Clock Service Light- The NX- can be programmed to illuminate the 'Service' LED when the internal clock has an invalid time due to power loss. (See location, page ) Manual Test- The NX- can be programmed to perform a bell and/or communicator test when [r]-[] is entered while the system is in the disarmed state. (See location, page ) On Board Zone Disable- The eight zones on the NX- panel can be disabled in order to have a completely wireless alarm system. (See location, page ) Partitions - The NX- can be partitioned into a maximum of eight separate systems with distinct reporting codes, user codes, and operating features for each system. (See locations -, pages 9-0) Program Code - The factory default for the 'Go To Program' code is [9]-[]-[]-[] when using a -digit code or, if the -digit option is used, the default is [9]-[]-[]-[]-[0]-[0]. The program code can also be used as an Arm/Disarm code. If used as an Arm/Disarm code, and open/close reports are sent, the user code will be. (See location, page ) Quick Arm Feature - The NX- has a one button 'Quick Arm' feature which can be used to arm the system by pressing the [Exit] key or the [Stay] key on the keypad. If closing reports are sent, the user code will be 9. (See location, page ) Recent Closing - If enabled, the NX- will send a 'Recent Closing Report' to the central station if an alarm occurs within minutes after the panel is armed. The user number that armed the system will also be sent. (See location, page ) Re-exit - The NX- has the ability to restart the exit delay for a quick exit without disarming the system by pressing the [Exit] key while the system is armed. (See location, page ) Shutdown- This mode will cause the keypads to turn off all LED=s, except the 'Power' LED, and not accept keypresses. (See location, page ) Page

6 Siren Blast For Arming- The NX- can be programmed to give a one second siren blast when the panel is armed, at the end of the exit delay, or when the central station receiver acknowledges the closing report. It can also give one blast for remote (keyswitch) arming and two blasts for remote disarming. (See location, page ) Siren Supervision - The NX- has a ASiren circuit that will constantly monitor the siren on the NX- and can be programmed to report if the wires are cut. (See location, page ) Silent Exit Option - The exit delay can be silenced by pressing [r]-[exit] before arming the control panel or when using the re-exit feature. The exit delay can also be silenced permanently in all partitions. (See location, page ) Start/End Programming and End Downloading- A report can be sent when local programming is started and ended. A report can also be sent when a download session ends. (See location, page ) Swinger Shutdown - This feature allows a zone or zones to be automatically bypassed after a specified number of alarms. When a zone is tripped, the alarm counter reflects in memory. If a new (first) alarm is detected in a different zone, the counter remains at. If an alarm is detected on a previously tripped zone, the count increments to. The counter will increment each time an alarm is detected on a zone with multiple trips. Bypassing will occur on the zone that causes the count to equal the number programmed in location ; the counter will reset to zero (0); and begin a new trip count where the next alarm will set the counter to. If immediate restore is enabled in location, the alarms (and restores, if enabled) will be sent as they occur. If immediate restore is not enabled, a second or subsequent alarm will not be sent until the siren times out. (See location and, page ) NOTE: For UL installations, this feature shall be disabled. Telephone Line Monitor - The NX- has a Telephone Line Monitor that monitors the voltage and current of the telephone line for a detection of a faulted phone line. This condition can also be reported to the central station. If the report is enabled, only the Telephone Line Restore will be reported unless the NX-0 is being used. (See locations, 9, and 0, pages -) Temporal Siren Disable - If disabled, the Fire Siren will be steady and Fire Voltage Out will be the same as Burglary (continuous). Otherwise, the Fire Siren will be temporal. (See location, page ) NOTE: For UL installations, do NOT disable. Tone Sniff Answering Machine Defeat- If enabled, only one call is required to defeat the answering machine. To use this feature you must have a Hayes 00 Smart Modem or a Caddx 00 module. From the computer, call the panel as normal. When the answering machine answers, the panel will hear the tones from the modem and seize the phone line for a download. (See location, page ) Two Call Answering Machine Defeat - If enabled, to defeat an answering machine, two telephone calls must be made to the premises. On the first call, let the phone ring one or two times. The control panel will detect these rings and start a second timer, during which, the control panel will answer the next call on the first ring. This is not recommended for commercial applications. (See location, page ) Walk-Test Mode - If enabled, entering [r] [Chime] followed by a user code will allow a walk-through zone test where all zones become silent and local (non-reporting). During this test the chime light will flash on the LED keypad. Each time a zone is faulted, the zone light on the LED keypad will illuminate and the chime will sound. The number of the faulted zone(s) will be displayed on the LCD keypad. It will also be entered into alarm memory and the internal log. To exit at any time during this mode, enter a user code. Otherwise the AWalk-Test will automatically exit after minutes. (See location, page ) Wireless Sensor Missing/Low Battery - The NX- will send a report to the central station when a wireless sensor has detected a low battery or has not reported to the receiver. The 'Service' LED will illuminate when either condition exists. (See location, page ) Zone Bypassed Sounder Alert- If this feature is enabled, the NX- will beep the keypad sounder upon arming if a zone is bypassed. (See location, page ) Zone Doubling - This feature allows you to use the eight zones on the panel as sixteen normally closed zones. When this feature is used European double E.O.L. configuration cannot be used on the first sixteen zones. THIS FEATURE DOES NOT INCREASE THE TOTAL NUMBER OF AVAILABLE ZONES BEYOND. If one of the sixteen zones must be a fire zone, it must be one of Zones to. The corresponding upper zone will become unavailable. For example, if Zone is a fire zone, then Zone will not be available. (See location, page ) Zone Types (Configurations) - The NX- has 0 programmable Zone Types that determine how each zone will function and report. The default Zone Types are listed on page. (See locations -9, pages -) Page

7 PROGRAMMING THE NX- LED KEYPADS This section describes how to program the address and partition of each keypad as well as the options that are available. The address of the keypad is important because this is how the panel supervises the keypads. The factory default for the Master code is []-[]-[]-[] when using a -digit code or []-[]-[]-[]-[]-[] for a -digit code. The factory default for the 'Go To Program' code is [9]-[]-[]-[] for a -digit code or [9]-[]-[]-[]-[0]-[0]fora -digit code. [r] [9] [] (Applies to LED keypad ONLY) ) Enter [r] [9] [] [program code]. ) Enter the zone number ( - ) you want the keypad to start at. ) Enter [r] to save and exit. [r]-[9]-[] Set keypad options ) Enter [r]-[9]-[] [program code]- The 'Service' LED will flash. ) LEDs - can now be toggled on/off to enable/disable the following functions: ) After enabling/disabling the desired functions press [r] LED Keypad Feature Enabled RESERVED. DO NOT PROGRAM THIS AT ALL! Enable Silent Keypad option. Silences the entry/exit sounder & chime only. Enable Ding Dong sound for Chime - If off, chime will be a single tone. (See location 0, page ) Enable Keypress Silence option (silences the pulsing keypad sounder for seconds when a key is pressed) Enable Armed Status Suppression (will not allow the keypad to display faulted or bypassed zones when the system is armed) Enable Panic, Fire, Medical Beeptone (will sound a short beep to verify that the keypress was accepted) Suppresses the 'Service' LED (NOTE: For UL installations, the Service LED shall not be suppressed.) (will not allow the 'Service' LED to illuminate for any reason. If there is a system trouble, pressing [r]-[] will still show the service menu.) Enable multi-partition viewing (enables temporary viewing of all partitions by pressing [r]-[]-[partition number]) [r]-[9]-[] Set Keypad Number and Partition ) Enter [r]-[9]-[]-[program code]- The 'Service' LED and the 'Instant' LED will flash. ) Enter the keypad number (-) ) Press [r]- The 'Instant' LED will illuminate steady and the'service' LED will remain flashing. ) Enter the partition number for the keypad (The keypad will automatically exit this mode at this time) [r]-[9]-[] Set elapsed increments since last autotest ) Enter [r]-[9]-[]-[program code]-the 'Service' LED will flash. ) Enter [00's digit] -[0's digit]-['s digit]-[#] [r]-[9]-[] Set system date ) Enter [r]-[9]-[]-[master code]. The 'Service' LED will flash. ) Enter [day of week (=Sun)]-[month 0's digit]-[month 's digit]-[day 0's digit] [day 's digit] -[year 0's digit]-[year 's digit] [r]-[9]-[] Set system clock ) Enter [r]-[9]-[]-[master code]. The 'Service' LED will flash. ) Enter [hour 0's digit]-[hour 's digit]-[minutes 0's digit]-[minutes 's digit] Page

8 CHANGING USER CODES: ) Enter [r]-[]-[master code] - The 'Ready' LED will flash. ) Enter the digit user number (always digits such as '0' for user ) - The 'Ready' LED will illuminate steady. ) Enter the new user code designated for that individual - The 'Ready' LED will flash indicating that the code was accepted. If it rejects the code, the sounder will beep times, Note for NX00 Series LED Keypad: The zone lights will illuminate indicating the first digit of the user code. (Lights - on = code is blank; lights - off = 0 ; lights and = 9.) Use the up and down scroll keys to view the next digit or enter a new - or -digit user code. While using the scroll keys you can change any digit by entering a new digit. This will advance you to the next digit. ) If another user code needs to be programmed, return to step. ) Press [#] while the 'Ready' LED is flashing to exit the User Code Programming Mode. ASSIGNING AUTHORITY LEVEL: ) Enter [r]-[]-[master code] - The 'Ready' LED will flash. ) Enter [ digit user number] (always digits such as 0 for user ) - The 'Ready' LED will illuminate steady and the 'Instant' LED will flash. Refer to the chart below for the description of each LED. Turn the LED on for the features that you desire. LED ATTRIBUTES IF LED IS OFF LED ATTRIBUTES IF LED IS ON Reserved Activate output # Arm Only Activate output # Arm Only After Close Window Activate output # Master arm/disarm (can program other codes) Activate output # Arm/disarm code Arm/disarm Allowed to bypass zones (see location ) Bypass Zones Code will send open / close reports Open / Close Reporting If this LED is on, LEDs - will use the chart to the right If this LED is off, LEDs - use the chart to the left ) Enter [r] - The 'Instant' LED will illuminate steady. This moves you to the partition enable. (This tells the system what partition this user can arm/disarm. LEDs - illuminate for each partition that the user has authorization for. To change any of these numbers, press - to permit or deny access to the user. (Example: If LED # is lit, then user has assigned access to that partition. By pressing the [] key, the LED will go off indicating the user has been denied access to that partition.) ) Enter [r] This returns you back to step above. At this point you may enter another user number to assign attributes for. You may continue this procedure until you have assigned authority levels to all user numbers - or - you may press [#] key to exit the Assigning Authority Level Program. NOTE: Any master arm/disarm code can add or change a user code if the master code has access to the same partitions as the code being added/changed. Consequently, when programming the user codes for a partitioned system, leave at least one code (can be 'go to program code' if enabled in location ) access to all partitions or you will not be able to add new users. If you desire the end user to be able to add new codes, you must remove the partition authority from all blank codes. [r]-[9]-[] Pressing [r]-[9]-[] while the system is disarmed will cause the control to do a callback for a download. NOTE: A valid user code may be required after [r]-[9]-[] if enabled in location, page. Fender leo banjo serial numbers. [r]-[9]-[9] Pressing [r]-[9]-[9] while the system is disarmed will cause the control panel to seize the phone line for a download. NOTE: A valid user code may be required after [r]-[9]-[9] if enabled in location. Page

9 PROGRAMMING THE NX- CONTROL ENTERING THE PROGRAM MODE: To enter the Program Mode, press [r]-[]. At this time, the five function LEDs (Stay, Chime, Exit, Bypass, & Cancel) will begin to flash. Next, enter the 'Go To Program Code' (FACTORY DEFAULT IS [9]-[]-[]-[]). If the 'Go To Program Code' is valid, the 'Service' LED will flash and the five function LEDs will illuminate steady. You are now in the Program Mode and ready to select the module to program. SELECTING THE MODULE TO PROGRAM: Since all modules connected to the NX- are programmed through the keypad, the module you are programming should be the first entry. To program the NX- Control Panel, enter [0]-[#]. The [0] is the module number of the control and the [#] is the entry key. Other module entry numbers can be found in their corresponding manuals. PROGRAMMING A LOCATION: Once the number of the module to be programmed has been entered, the 'Armed' LED will illuminate, indicating it is waiting for a programming location to be entered. Any location can be accessed by directly entering the desired programming location followed by the pound [#] key. If the location entered is a valid location, the 'Armed' LED will extinguish, the 'Ready' LED will illuminate and the binary data for the first segment of this location will be shown by the zone LED's. While entering new data, the 'Ready' LED will begin flashing to indicate a data change in process. The flashing will continue until the new data is stored by pressing the [r] key. Upon pressing the [r] key, the keypad will advance to the next segment and display its data. This procedure is repeated until the last segment is reached. Pressing the [#] key will exit from this location, and the 'Armed' LED will illuminate again waiting for a new programming location to be entered. If the desired location is the next sequential location, press the [POLICE] key. If the previous location is desired press the [FIRE] key. If the same location is desired press the [MEDIC] key. To review the data in a location, repeat the above procedure, pressing the [r] key without any numeric data entry. Each time the [r] key is pressed, the programming data of the next segment will be displayed for review. EXITING A LOCATION: After the last segment of a location is programmed, pressing the [r] key will exit that location, turn the 'Ready' LED off and the 'Armed' LED on. The [r] key must be pressed or the data will not be saved. To exit before the last segment, press [#]. As before, you are now ready to enter another programming location. If an attempt is made to program an invalid entry for a particular segment, the keypad sounder will emit a triple error beep (beep, beep, beep), and remain in that segment awaiting a valid entry. EXITING THE PROGRAM MODE : When all the desired changes in programming have been made, it is time to exit the program mode. Pressing the [Exit] key will exit this programming level, and go to the 'Select a Module To Program' level. If no additional modules are to be programmed, pressing the [Exit] key again will exit the program mode. If there is a module to be programmed, it may be selected by entering its address followed by the [#] key (see 'Selecting the Module To Program' above). The procedure for programming these devices is the same as for the control panel, except the locations will be for the module selected. PROGRAMMING DATA Programming data is always one of two types. One type of data is numerical and can take on values from 0 - or 0 - depending on the location's segment. The other type of data is a feature selection type. Feature selection data is used to turn features on or off. Use the following procedures when working with these two data types: NUMERICAL DATA: Numerical data is programmed by entering a number from 0- on the numeric keys of the system keypad. To view the data in a location, a binary process is used. With this process, the LED=s for zones through are utilized, and the numeric equivalents of their illuminated LED=s are added together to determine the data in a programming location. The numeric equivalents of these LED=s are as follows: ZoneLED= ZoneLED= ZoneLED= ZoneLED= ZoneLED= ZoneLED= ZoneLED= ZoneLED= Example: If the numerical data to be programmed in a location is ', press []-[] on the keypad. The LED=s for Zone and Zone will become illuminated indicating is in that location ( + = ). See this example on page 0. Once the data is programmed, press the [r] key to enter the data and advance to the next segment of that location. After the last segment of a location is programmed, pressing the [r] key will exit that location, turn the 'Ready' LED off and the 'Armed' LED on. As before, you are now ready to enter another programming location. If an attempt is made to program a number too large for a particular segment, the keypad sounder will emit a triple beep, indicating an error, and remain in that segment awaiting a valid entry. On the LCD keypad, the number in the location will be displayed. For locations with a maximum of, the hexidecimal equivalent will be displayed in parenthesis. Example: (B) or (E). Page 9

10 PROGRAMMING EXAMPLE TO BE INSERTED HERE. Page 0

11 FEATURE SELECTION DATA: Feature selection data will display the current condition (on or off) of eight features associated with the programming location and segment selected. Pressing a button on the touchpad ( thru ) that corresponds to the 'feature number' within a segment, will toggle (on/off) that feature. Pressing any numeric key between [] and [] for selection of a feature, will make the corresponding LED illuminate (feature ON). Press the number again, and the LED will extinguish (feature OFF). You will see that numerous features can be selected from within one segment. For instance, if all eight features of a segment are desired, pressing []-[]-[]-[]-[]-[]-[]-[] will turn on LED's thru as you press the keys, indicating that those features are enabled. LCD Keypad Users Note: The numbers of the enabled features will be displayed. However, the features not enabled will display a hyphen (-). After the desired setting of features is selected for this segment, press the [r] key. This will enter the data and automatically advance to the next segment of the location. When you are in the last segment of a location and press the [r] to enter the data, you will exit that location. This will now turn the 'Ready' LED off and the 'Armed' LED on. As before, you are now ready to enter another programming location. LOADING FACTORY DEFAULTS To load the factory defaults, enter the program mode using the procedure on page 9, then type [9]-[]-[0]-[#]. The keypad will beep times indicating that the loading is in progress. The loading takes about seconds. ENROLLING MODULES AND KEYPADS For supervision purposes, the NX- has the ability to automatically find and store in its memory, the presence of all keypads, zone expanders, wireless receivers, and any other module connected to the data terminal. This allows these modules to be supervised by the control panel. To enroll the modules, enter the Program Mode of the NX- control panel as described on page 9. When the Program Mode is exited, the NX- control will automatically enroll the devices. The enrolling process takes about seconds, during which time the 'Service' LED will illuminate. User codes will not be accepted during the enrolling process. If a speaker is attached to the NX-, it will click at this time. If a siren or bell is attached to the NX-, it will sound for about second. Once a module is enrolled, if it is not detected by the control, the 'Service' LED will illuminate. L QUICK START INSTALLATION For most routine installations, the 'Quick Start' option will allow for enabling a majority of the options available with the NX-, when communicating in Contact ID or SIA formats and without partitioning. The 'Quick Start' locations can be identified by the L symbol. CONTROL PANEL PROGRAMMING LOCATIONS L LOCATION 0 - PHONE NUMBER (0 segments, numerical data) The first telephone number is programmed in location 0. A ' indicates the end of the phone number. Delays of four seconds can be programmed at any point in the phone number by programming a ' in the appropriate segment. If tone dialing is desired, program a ' in the segment where tone dialing should begin. If the entire number should be tone dialing, program a ' in the first segment. Program an A' for a and a A' for a L LOCATION - ACCOUNT CODE FOR THE PHONE # ( segments, numerical data) The account code sent when Phone # is dialed is programmed in location. Program a A0' in the segment immediately after the last digit of the account code. If the account code is digits long, program all segments. L LOCATION - COMMUNICATOR FORMAT FOR PHONE # ( segment, numerical data) Location contains the communicator format used to transmit to the receiver connected to Phone #. Consult the instructions for your central station receiver to determine which format is compatible. Select a format from the list on the following page. If you require a format other than those listed, review the override options described in location, to build the appropriate format. A ' must be programmed in location in addition to the entries in location in order to create a special format. If this location contains a '0', the built-in communicator will be disabled, and the NX- will function as a local only control. L LOCATION - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE # ( segments, numerical data) Segment - Dial attempts: Location, Segment is used to enter the number of dial attempts ( to Attempts) the communicator will make to Phone # before ending the notification process. Factory default is ' and the communicator will make eight () attempts to the first number. Page

12 Segment - Phone # Backup Control: Programming a '0' in Segment of this location will cause the NX- to make the designated number of attempts to Phone # before setting the 'Fail To Communicate' condition and stop reporting. Programming a ' in this segment will cause the NX- to stop trying to communicate after the designated number of attempts have been made to Phone #. If a ' is programmed in this segment, it will cause the NX- to make the dial attempts in increments of two. The first two attempts will be made to Phone #, the next two attempts to Phone #, then repeating until the total number of attempts designated in Segment is completed. FORMAT SELECTIONS DATA FORMAT DESCRIPTION 0 Local Communicator is disabled Universal + Two digit event code 00hz transmit 00hz handshake double round parity 0pps + fast (or +) One digit event code 900Hz transmit 00Hz handshake double round parity 0pps Reserved Reserved Pager digit event code DTMF transmission / or / slow 00hz transmit 00hz handshake double round parity 0 p.p.s. hex capability / or / slow 00hz transmit 00hz handshake double round parity 0 p.p.s. hex capability / or / fast 00hz transmit 00hz handshake double round parity 0 p.p.s. hex capability / or / fast 00hz transmit 00hz handshake double round parity 0 p.p.s. hex capability 9 / or / fast with parity 00hz transmit 00hz handshake single round w/parity 0 p.p.s. hex capability 0 / or / fast with parity 00hz transmit 00hz handshake single round w/parity 0 p.p.s. hex capability + express digit event code DTMF transmission + fast Two digit event code 900hz transmit 00hz handshake double round parity 0 p.p.s. Ademco Contact ID DTMF (see pages -) SIA FSK (see pages -) Custom format (See location, page ) REPORTING EVENTS TO PHONE NUMBER Phone # has two programming locations that are used to select which events are reported to this phone number. Location is used to select which events are reported to Phone #. Location is used to select which partitions are reported to Phone #. If dual or split reporting is not desired, location should be used to select all events to Phone # and location should be left at the factory default of '0'. If dual or split reporting is desired, and the split is based on the event type (such as alarm, open/close, etc.), location should be used to select only those events that should be reported to Phone # and location should be left at the factory default of '0'. If dual or split reporting is desired, and the split is based on partition, location should be programmed as a '0' and location should be used to select those partitions that should be reported to Phone #. If no events should be reported to Phone #, both locations should be programmed as '0' (disabling all options). LOCATION - EVENTS REPORTED TO PHONE # ( segments, feature selection data) Segment : = Alarms and Alarm Restores. = Opening and Closings. = Zone Bypass and Bypass Restores. = Zone Trouble and Trouble Restores. = Power Fail, Low Battery, Power Restore, and Low Battery Restore. = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore. = Test Reports. = Start and End programming, Download complete. Page

13 Segment : = Zone and Box Tamper and Tamper Restore. = Auxiliary Power Overcurrent, Ground Fault, and Restore for both. = Wireless Sensor Missing and Restore. = Wireless Sensor Low Battery and Restore. = Expander Trouble and Restore. = Fail To Communicate. = Reserved. = Reserved. LOCATION - PARTITIONS REPORTED TO PHONE # ( segment, feature selection data) Location is used when events to be reported to a phone number are based upon the partition regardless of the event. If this location is used, location should be programmed as '0'. Segment : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # L LOCATION - PROGRAMMING PHONE # (0 segments, numerical data) Phone # is programmed in location. A ' indicates the end of the phone number. Delays of four seconds can be programmed at any point in the phone number by programming a ' in the appropriate segment. If tone dialing is desired, program a ' in the segment where tone dialing should begin. If the entire number should be tone dialing, program a ' in the first segment. Program an A' for a and a A' for a L LOCATION - ACCOUNT CODE FOR THE PHONE # ( segments of numerical data) The account code sent when Phone # is dialed is programmed in location. Program a A0' in the segment immediately after the last digit of the account code. If the account code is digits long, program all segments. If this location is left unprogrammed, account code will be used when the second phone number is dialed. L LOCATION - COMMUNICATOR FORMAT FOR PHONE # ( segment, numerical data) Location contains the communicator format used to transmit to the receiver connected to Phone #. Consult the instruction manual for your central station receiver to determine which format is compatible, and select from the formats listed on page. If you require a format other than those listed, review the override options described in Location to build the appropriate format. A ' must be programmed in location in addition to the entries in location in order to create a special format. If this location contains a '0', format will be used when Phone # is dialed. LOCATION 9 - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE # ( segments, numerical data) Segment, Dial attempts: Segment of Location 9 is used to enter the number of dial attempts ( to attempts) the communicator will make to Phone # before ending the notification process. Factory default is ' and the communicator will make the same number of attempts as those programmed in location. Segment, Phone # Backup Control: Programming a '0' in Segment of this location will cause the NX- to make the designated number of attempts to Phone # before setting the 'Fail To Communicate' condition and stop reporting. Programming a ' in this segment will cause the NX- to stop trying to communicate after the designated number of attempts have been made to Phone #. If a ' is programmed in this segment, it will cause the NX- to make the dial attempts in increments of two. The first two attempts will be made to Phone #, the next two attempts to Phone #, then repeating until the total number of attempts designated in Segment is completed. Page

14 REPORTING EVENTS TO PHONE NUMBER Phone # can be used to back up Phone # or for a second receiver to multi-report or split report events. Phone # has two programming locations that are used to select which events are reported to this phone number. Location 0 is used to select which events are reported to Phone #, and location is used to select which partitions are reported to Phone #. If dual or split reporting is not desired, location 0 and location should be left at the factory default of '0'. If multi-reporting or split reporting is desired, and the split is based on the event type (such as alarm, open close etc.), location 0 should be used to select only those events that should be reported to Phone #, and location should be left at the factory default of '0'. If dual or split reporting is desired, and the split is based on partition, then location 0 should be programmed as '0', and location should be used to select those partitions that should be reported to the Phone #. If no events should be reported to Phone #, both locations should be '0'. LOCATION 0 - EVENTS REPORTED TO PHONE # ( segments of feature selection data) Segment : Segment : = Alarms and Alarm Restores. = Opening and Closings. = Zone Bypass and Bypass Restores. = Zone Trouble and Trouble Restores. = Power Fail, Low Battery, Power Restore, and Low Battery Restore. = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore. = Test Reports. = Start and End programing, Download complete. = Zone and Box Tamper and Tamper Restore. = Auxiliary Power Overcurrent and Ground Fault and Restore for both. = Sensor Missing and Restore. = Sensor Low Battery and Restore. = Expander Trouble and Restore. = Fail To Communicate. = Reserved. = Reserved. LOCATION - PARTITIONS REPORTED TO PHONE # ( segment, feature selection data) Location is used when events to be reported to a phone number are based upon the partition regardless of the event. If this location is used, location 0 should be '0'. Segment : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # LOCATION - PROGRAMMING PHONE # (0 segments, numerical data) Phone # is programmed in location. A ' indicates the end of the phone number. Delays of four seconds can be programmed at any point in the phone number by programming a ' in the appropriate segment. If tone dialing is desired, program a ' in the segment where tone dialing should begin. If the entire number should be tone dialing, program a ' in the first segment. Program an A' for a and a A' for a LOCATION - ACCOUNT CODE FOR PHONE # ( segments, numerical data) The account code sent when Phone # is dialed is programmed in location. Program a A0' in the segment immediately after the last digit of the account code. If the account code is digits long, program all segments. If location is left unprogrammed, account code will be used when the Phone # is dialed. LOCATION - COMMUNICATOR FORMAT FOR PHONE # ( segment, numerical data) Location contains the communicator format used to transmit to the receiver connected to phone #. Consult the instruction manual for your central station receiver to determine which format is compatible, and select from the formats listed on page. If you require a format other than those listed, review the override options described in Location to build the appropriate format. A ' must be programmed in location in addition to the entries in location in order to create a special format. If this location contains a '0', format will be used when Phone # is dialed. Page

15 LOCATION - DIAL ATTEMPTS/BACKUP CONTROL FOR PHONE # ( segments, numerical data) Segment, Dial Attempts: Segment of Location is used to enter the number of dial attempts ( to attempts) the communicator will try to Phone # before ending the notification process. Factory default is ' and the communicator will make the same number of attempts as those programmed in location. Segment,Phone#Backup Control: Programming a '0' in Segment of this location will cause the NX- to make the designated number of attempts to Phone # before setting the 'Fail To Communicate' condition and stop reporting. Programming a ' in this segment will cause the NX- to stop trying to communicate after the designated number of attempts have been made to Phone #. If a ' is programmed in this segment, it will cause the NX- to make the dial attempts in increments of two. The first two attempts will be made to Phone #, the next two attempts to Phone #, then repeating until the total number of attempts designated in Segment is completed. REPORTING EVENTS TO PHONE NUMBER Phone # can be used for a third receiver to multi-report or split report events. Phone # has two programming locations that are used to select which events are reported to this phone number. Location is used to select which events are reported to Phone #, and Location is used to select which partitions are reported to Phone #. If dual or split reporting is not desired, location and location should be left at the factory default of '0'. If multi-reporting or split reporting is desired and the split is based on the event type (such as alarm, open/close, etc.), then location should be used to select only those events that should be reported to Phone # and location should be left at the factory default of '0'. If dual or split reporting is desired, and the split is based on partition, then location should be programmed to '0' and location should be used to select those partitions that should be reported to Phone #. If no events should be reported to Phone #, both locations should be '0'. LOCATION - EVENTS REPORTED TO PHONE # ( segments, feature selection data) Segment : = Alarms and Alarm Restores. = Opening and Closings. = Zone Bypass and Bypass Restores. = Zone Trouble and Trouble Restores. = Power Fail, Low Battery, Power Restore, and Low Battery Restore. = Bell Cut, Telephone Line Cut, Bell Cut Restore, Telephone Line Restore. = Test Reports. = Start and End programming, Download complete. Segment : = Zone and Box Tamper and Tamper Restore. = Auxiliary Power Overcurrent and Ground Fault and Restore for both. = Sensor Missing and Restore. = Sensor Low Battery and Restore. = Expander Trouble and Restore. = Fail To Communicate. = Reserved. = Reserved. LOCATION - PARTITIONS REPORTED TO PHONE # ( segment, feature selection data) Location is used when events to be reported to a phone number are based upon the partition regardless of the event. If this location is used, location should be '0'. Segment : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # Page

16 LOCATION - CUSTOM COMMUNICATOR FORMAT (See locations,, &) Segment : Segment : = On for 00hz transmit; Off for 900hz. = On for 00hz handshake; Off for 00hz. = On for cksum parity; Off for double round parity. = On for digit event code; Off for digit event code. = Reserved. = Reserved. = On for 0 p.p.s.; Off for 0 or 0 p.p.s. = On for 0 p.p.s.; Off for 0 or 0 p.p.s. = On for pager format (no handshake required). = On for 00/00 handshake. = Reserved = Reserved. = On for Contact ID. = On for SIA. = On for Contact ID or +. = On for DTMF. Segment & : Reserved. L LOCATION 9 - DOWNLOAD ACCESS CODE ( segments, numerical data) Location 9 contains the eight digit access code the NX- must receive from the downloading software before the panel will permit downloading to occur. The factory default code is L LOCATION 0 - NUMBER OF RINGS TO ANSWER ( segment, numerical data) Location 0 contains the number of rings to answer for a download. Enter a number from A0' (disabled) to '. Factory default is ' and the NX- will answer on rings. L LOCATION - DOWNLOAD CONTROL ( segment, feature selection data) Location contains the feature selections for the controlling of download sessions. The following features can be enabled or disabled using this location. (See the feature definitions beginning on page ) Segment : - On enables two call answering machine defeat. - On enables tone sniff answering machine defeat. - On requires call back before download session. - Shutdown (can only be viewed from the keypad, must be changed through downloading). - On locks all local programming. (can only be viewed from the keypad, must be changed through downloading) - On locks programming of all locations associated with the communicator (can only be viewed from the keypad, must be changed through downloading) - On locks out download section. (can only be viewed from the keypad, must be changed through downloading. If 'On', locations 9 - cannot be viewed from the keypad; can only be viewed from the keypad when 'Off'.) - On enables call back at auto test interval. L LOCATION - DOWNLOAD CALL BACK NUMBER (0 segments, numerical data) If a telephone number is programmed into this location, and 'Require Callback' is enabled in location, the control panel will hang up for approximately seconds (ensuring that the calling party has disconnected), and then call back. If tone dialing is desired, program an ' in the segment where tone dialing should begin. If the entire number should be tone dialing, program an A' in the first segment. Four-second delays can be obtained anywhere in the sequence by programming a ' in the appropriate delay location. WARNING: THE CALLBACK PHONE NUMBER SHOULD ALWAYS BE REVIEWED FOR ACCURACY BEFORE DISCONNECTING. Page

17 L LOCATION - PARTITION, FEATURE AND REPORT SELECTIONS ( segments, feature selection data) Location is used to enable certain features that can be accessed or are visible to the user from the keypad of the system. In addition, certain communicator reports are enabled in location. Each of these features can be enabled by partition. For additional partition information see locations -09 on pages 0-. If the feature selection location for any partition is left blank, that partition will use this location for the feature selection. This location contains segments of features each. (See the feature definitions beginning on page.) Segment : Segment : Segment : - On enables the Quick Arm feature. - On enables the Re-exit feature. - On enables the Automatic Bypass feature. - On enables the Silent Keypad Panic feature (overrides the audible panic selection). - On enables the Audible Keypad Panic feature. - On enables the Keypad Aux feature (FIRE). - On enables the Keypad Aux feature (MEDICAL). - On enables the Keypad Multiple Code Attempt Tamper feature. - On enables the LED Extinguish feature. - On enables the Require Code for Bypassing feature. - On enables the Zone Bypassed Sounder Alert feature. - On enables the AC Power/Low Battery Sounder Alert feature. - On enables Bypass toggle. - On enables Silent Auto Arm. - On enables the Automatic Instant feature. - Reserved. - On enables Opening and Closing reports. - On enables Zone Bypass reporting. - On enables Zone Restore reporting. - On enables Zone Trouble reporting. - On enables Zone Tamper reporting. - On enables the Cancel reporting. - On enables the Recent Closing report. - On enables the Exit Error report. L LOCATION - ENTRY / EXIT TIMERS ( segments, numerical data) Location is used to program the Entry/Exit times. There are separate Entry/Exit times. Segment, Entry time : This is the entry time that will be used when a delay zone type initiates an entry delay Valid entries are 0- seconds. Segment, Exit time : This is the exit time that will be used for all zones designated as delay. Valid entries are 0- seconds. Segment, Entry time : This is the entry time that will be used when a delay zone type initiates an entry delay. Valid entries are 0- seconds. Segment, Exit time : This is the exit time that will be used for all zones designated as delay. Valid entries are 0- seconds. Page

18 DEFAULT ZONE TYPES (Configurations) Zones can be programmed to be one of twenty different zone types (configurations). Zone types # - 0 can be used for wireless or hardwired zones using European double EOL configuration. The default zone types are listed below. These zone types can be customized by programming locations 0-9. DATA DESCRIPTION OF DEFAULT ZONE TYPES ' DAY ZONE - Instant when system is armed trouble zone when system is disarmed. -HOUR AUDIBLE - Creates an instant yelping siren alarm regardless of the armed state of the control ' panel. ENTRY/EXIT DELAY - A trip will start entry delay. The lack of a trip during exit delay will enable the ' Automatic Bypass or Instant mode if so programmed. FOLLOWER WITH AUTO- BYPASS DISABLED - This zone will be instant when the system is armed ' and no entry or exit delays are being timed. It is delayed during entry and exit delay times. This zone will not automatically bypass even if enabled in Segment of Location. INTERIOR FOLLOWER WITH AUTO- BYPASS ENABLED - This zone will be instant when the system ' is armed and no entry or exit delay is being timed. It is delayed during entry and exit delay times. This zone will automatically bypass if enabled in Segment of Location. ' INSTANT - This zone creates an instant alarm whenever it is tripped and the Armed LED is on. -HOUR SILENT - Creates an instant silent alarm regardless of the armed state of the control panel. It ' will not display on the keypad. FIRE - This zone will light the Fire LED and sound the temporal siren each time the zone is shorted. It will ' also rapidly flash the Fire LED indicating a trouble if the zone is open. ENTRY/EXIT DELAY - A trip will start entry delay. The lack of a trip during exit delay will enable the '9' Automatic Bypass or Instant mode if so programmed. -HOUR SILENT SUPERVISED- Creates an instant silent alarm regardless of the armed state of the '0' control panel. It will display on the keypad. KEYSWITCH ZONE - This zone type will arm and disarm the partition or partitions of the control panel ' that it resides in each time the zone is shorted. Keyswitch arming will report as user #99. INTERIOR FOLLOWER WITH 'CROSS ZONE' ENABLED - This zone will be instant when the system is armed and no entry or exit delay is being timed. It is delayed during entry and exit delay times. If a ' 'Cross Zone' is not being timed it will start a 'Cross Zone' timer. If a 'Cross Zone' is being timed it will create an instant alarm. This zone will automatically bypass when enabled in Segment of Location. INSTANT ENTRY GUARD - This zone creates an instant alarm whenever it is tripped and the Stay LED ' is off. It will start an entry delay time if it is tripped and the system is armed and the Stay LED is on. ENTRY/EXIT DELAY WITH GROUP BYPASS ENABLED - A trip will start entry delay. This zone will ' bypass when the 'Group Bypass' command is entered at the keypad. The lack of a trip during exit delay will enable the Automatic Bypass or Instant mode if so programmed. INTERIOR FOLLOWER WITH GROUP BYPASS ENABLED - This zone will be instant when the system is armed and no entry or exit delays are being timed. It is delayed during entry/exit delay times. This zone ' will bypass when the 'Group Bypass' command is entered at the keypad. This zone will automatically bypass if enabled in Segment of Location. INSTANT WITH GROUP BYPASS ENABLED - This zone creates an instant alarm whenever it is ' tripped and the Armed LED is on. This zone will bypass when the 'Group Bypass' command is entered at the keypad. ENTRY/EXIT DELAY WITH TAMPER ENABLED- A trip will start entry delay. The lack of a trip ' during exit delay will enable the Automatic Bypass or Instant mode if so programmed. This zone type can be used to enable tamper on a wireless transmitter. INTERIOR FOLLOWER WITH TAMPER AND AUTO-BYPASS ENABLED - This zone will be instant when the system is armed and no entry or exit delay is being timed. It is delayed during entry and exit ' delay times. This zone will automatically bypass if enabled in Segment of Location. This zone type can be used to enable tamper on a wireless transmitter. INSTANT WITH TAMPER ENABLED - This zone creates an instant alarm whenever it is tripped and the '9' Armed LED is on. This zone type can be used to enable tamper on a wireless transmitter. ENTRY/EXIT DELAY WITH TAMPER ENABLED-A trip will start entry delay. The lack of a trip during '0' exit delay will enable the Automatic Bypass or Instant mode if so programmed. This zone type can be used to enable tamper on a wireless transmitter. Page

19 NOTE: To null a zone, program the zone in Partition Select as zero (0) in all partitions and do not use end-of-line resistors. L LOCATION - ZONES - ZONE TYPE ( segments, numerical data) Location contains the Zone Type for zones -. Segment is for zone, and Segment is for zone. Default Zone Types are found in the table on page. To customize a Zone Type, see page. LOCATION - PARTITION SELECT, ZONES - ( segments, feature selection data) Location is used to select the partition(s) that zones - reside in. A zone may reside in any combination of the partitions. If a burglary zone resides in more than partition, it will only be active when all partitions it resides in are armed. A zone that resides in more than partition will be reported to its lowest partition number. Location has segments. Segment corresponds to zone, and Segment corresponds to zone. Segments - : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # L LOCATION - ZONES 9- ZONE TYPE ( segments, numerical data) Location contains the Zone Type for zones 9 -. Segment is for zone 9, Segment is for zone. Default Zone Types are found in the table on page. To customize a Zone Type, see page. LOCATION - PARTITION SELECT, ZONES 9- ( segments, feature selection data) Location is used to select the partition(s) that zones 9- reside in. A zone may reside in any combination of the partitions. If a burglary zone resides in more than partition, it will only be active when all partitions are armed. A zone that resides in more than partition will be reported to its lowest partition. Location has segments. Segment corresponds to zone 9 and Segment corresponds to zone. Segments - : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # L LOCATION 9 - ZONES - ZONE TYPE ( segments, numerical data) Location 9 contains the Zone Type for zones -. Segment is for zone, Segment is for zone. Default Zone Types are found in the table on page. To customize a Zone Type, see page. LOCATION 0 - PARTITION SELECT, ZONES - ( segments, feature selection data) Location 0 is used to select the partition(s) that zones - reside in. A zone may reside in any combination of the partitions. If a burglary zone resides in more than partition, it will only be active when all partitions are armed. A zone that resides in more than partition will be reported to its lowest partition. Location 0 has segments. Segment corresponds to zone and Segment corresponds to zone. Segments - : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # Page 9

20 L LOCATION - ZONES - ZONE TYPE GROUP ( segments, numerical data) Location contains the Zone Type for zones -. Segment is for zone, Segment is for zone. Default Zone Types are found in the table on page. To customize a Zone Type, see page. LOCATION - PARTITION SELECT, ZONES - ( segments, feature selection data) Location is used to select the partition(s) that zones - reside in. A zone may reside in any combination of the partitions. If a burglary zone resides in more than partition it will only be active when all partitions are armed. A zone that resides in more than partition will be reported to its lowest partition. Segment corresponds to zone and Segment corresponds to zone. Segments - : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # L LOCATION - ZONES -0 ZONE TYPE ( segments, numerical data) Location contains the Zone Type for zones -0. Segment is for zone Segment is for zone 0. Default Zone Types are found in the table on page. To customize a Zone Type, see page. LOCATION - PARTITION SELECT, ZONES -0 ( segments of feature selection data) Location is used to select the partition(s) that zones -0 reside in. A zone may reside in any combination of the partitions. If a burglary zone resides in more than partition, it will only be active when all partitions are armed. A zone that resides in more than partition will be reported to its lowest partition. Segment corresponds to zone and Segment corresponds to zone 0. Segments - : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # L LOCATION - ZONES - ZONE TYPE ( segments of numerical data) Location contains the Zone type for zones -. Segment is for zone Segment is for zone. Default Zone Types are found in the table on page. To customize a Zone Type, see page. LOCATION - PARTITION SELECT, ZONES - ( segments, feature selection data) Location is used to select the partition or partitions that zones - reside in. A zone may reside in any combination of the partitions. If a burglary zone resides in more than partition it will only be active when all partitions are armed. A zone that resides in more than partition, will be reported to its lowest partition. Location has segments. Segment corresponds to zone and Segment corresponds to zone. Segments - : = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # = Partition # Page 0

Control/Communicator Installation Manual

DAS NETWORX NX-8 Control/Communicator Installation Manual Page General Description.. 2 Ordering Information.. 2 Option Definitions.. 2 Programming the LED Code Pads.. 4 Programming the NX-8.. 8 Types

More information

NX-8 Installation manual Page 1 Date 13/03/04

NetworX NX-8 Installation Manual NX-8 Installation manual Page 1 Date 13/03/04 CONTENTS CONTENTS..2 GENERAL INFORMATION..4 ORDERING INFORMATION..4 FEATURE DEFINITIONS..5 PROGRAMMING THE NX-8 KEYPADS..12

More information

NX-8V2 Control Panel Installation Manual

NX-8V2 Control Panel Installation Manual P/N I-NX8V2-IM REV H ISS NOV12 Copyright Disclaimer Trademarks and patents Intended use Contact information Customer support 2012 UTC Fire & Security Americas Corporation,

More information

Series. NX-6-EUR Control Panel. Installation manual

GE Security NetworX TM Series NX-6-EUR Control Panel Installation manual NX-6-EUR Installation manual Page 2 28/04/05 CONTENTS CONTENTS..3 GENERAL INFORMATION..5 ORDERING INFORMATION..5 FEATURE DEFINITIONS..6

More information

UL approved for ANSI/SIA CP-01-2000. NetworX Series. NX-8E Control Panel Installation and Startup

UL approved for ANSI/SIA CP-0-000 NetworX Series NX-E Control Panel Installation and Startup 00 GE Security All rights reserved. These instructions do not purport to cover all details or variations in

More information

NetworX NX-6V2. LED Keypad User Manual

NetworX NX-6V2 LED Keypad User Manual POWER Light is on when AC power is present; flashes to indicate a low battery condition. ARMED Light is on when armed; off when disarmed; flashes to indicate a previous

More information

SECURITY SYSTEM NOTES

SECURITY SYSTEM NOTES Installing/Service Company For Service Call Central Station Duress Code FUNCTION CODES Function Code Controls Function This system is is not partitioned. EMERGENCY ACTIVATION KEYS

More information

SECURITY SYSTEM NOTES. EMERGENCY ACTIVATION KEYS (check if enabled) PROGRAMMED FUNCTIONS

SECURITY SYSTEM NOTES Installing/Service Company For Service Call Installation Date / / Central Station Duress Code EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary Emergency Police PROGRAMMED

More information

SECURITY SYSTEM NOTES

SECURITY SYSTEM NOTES Installing/Service Company For Service Call Central Station Duress Code FUNCTION CODES Function Code Controls Function EMERGENCY ACTIVATION KEYS (check if enabled) Fire Auxiliary

More information

Understanding the Code Pad lights..4. Code Pad tones..5. Fully arming the system On MODE..6. Fully arming the system - Quick Arm MODE..

TABLE OF CONTENTS..Glossary of terms..2..code Pad Diagram..3 Understanding the Code Pad lights..4 Code Pad tones..5 Fully arming the system On MODE..6 Fully arming the system - Quick Arm MODE..6

More information

NetworX Series. NX-148E LCD Keypad. User Manual

NetworX Series NX-148E LCD Keypad User Manual TABLE OF CONTENTS I. GLOSSARY OF TERMS.. 3 II. UNDERSTANDING THE LIGHTS.. 4 III. KEYPAD FUNCTIONS.. 5 ARMING YOUR SYSTEM IN THE AWAY MODE.. 5 MAKING YOUR

More information

Solution-16 Operators Manual ISSUE 1.60

Solution-16 Operators Manual ISSUE 1.60 !'#$%&'()*+ Operators Manual Copyright 2002 by, SYDNEY, AUSTRALIA Document Part Number MA880O DOCUMENT ISSUE 1.60 Printed 22 March 2002 This documentation is provided

More information

NetworX Series. NX- 4/8 Code Pad. User Manual (Australian Version)

NetworX Series NX- 4/8 Code Pad User Manual (Australian Version) Table Of Contents Code Pad Diagram.. Inside Front Glossary of Terms..2 Understanding the Code Pad lights..3 Code Pad Tones..4 Fully

More information

Application Notes. 1.21 Partition Programming (PC1616/1832/1864 V4.2) Page 42. Panels: POWER SERIES (PC1616/1832/1864 V4.

Application Notes 1.21 Partition Programming (PC1616/1832/1864 V4.2) Panels: POWER SERIES (PC1616/1832/1864 V4.2) Overview: The PC1616 supports 2 true partitions. The PC1832 supports 4 true partitions.

More information

ICP-CC488. Installation Guide ICP-CC488 Control Panel

ICP-CC488 EN Installation Guide ICP-CC488 Control Panel ICP-CC488 Installation Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems,

More information

IDS. Users Guide to Keypad Functions S E C U R I T Y MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18

INHEP DIGITAL IDS S E C U R I T Y Users Guide to Keypad Functions MANUAL NO. 700-171-01B ISSUED AUG 2002 VERSION 1.18 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Away Arm Stay

More information

VISTA-128FBP VISTA-250FBP Commercial Fire and Burglary Partitioned Security Systems with Scheduling

VISTA-128FBP VISTA-250FBP Commercial Fire and Burglary Partitioned Security Systems with Scheduling User Guide K0377V2 7/09 Rev. C 2 TABLE OF CONTENTS SYSTEM OVERVIEW.. 5 General.. 5 A Partitioned System..

More information

!'#$%&'()**+),-+)).( /'0%1##1%&'(21'$1#( ISSUE 1.40

!'#$%&'()**+),-+)).( /'0%1##1%&'(21'$1#( ISSUE 1.40 MA8XXI 34&0(5167(410(877'(&'9#$:7:(;'

More information

Program Entry Guide. Control Panels

EN Program Entry Guide Control Panels D6412/D4412 Program Entry Guide EN 2 Documentation Conventions Type Styles Used in this Manual To help identify important items in the text, the following type styles

More information

IDS X-Series User Manual 700-398-01D Issued July 2012

1 2 Contents 1. Introduction to the IDS X-Series Panels.. 7 2. Before Operating Your Alarm System.. 7 3. Understanding the Keypad LEDs.. 8 3.1 Viewing Data on an LED Keypad.. 12 3.1.1 LED Status Indicators..

More information

SPECIAL CODES AUXILIARY CODES SYSTEM NOTES

Installing/Service Company Monitoring Center SPECIAL CODES Master Code Duress Code AUXILIARY CODES 'Quick Arm' ' Chime' 08 02 09 03 10 04 11 05 12 06 13 07 14 SYSTEM NOTES Exit Delay Time Entry Delay Time

More information

Solution 862 Operators Manual. Issue 1.00

Solution 862 Operators Manual Issue 1.00 Solution 862 Operators Manual Copyright 1998 by Electronics Design and Manufacturing Pty Limited, SYDNEY, AUSTRALIA Document Part Number MA406O Document Issue

More information

NetworX Series. NX-216E Zone Expander Module Installation and Startup

NetworX Series NX-E Zone Expander Module Installation and Startup 00 GE Security All rights reserved. These instructions do not purport to cover all details or variations in equipment nor to provide every

More information

SECURITY SYSTEM NOTES SPECIAL CODES AUXILIARY ARM / DISARM CODES ENTRY / EXIT DELAY TIMES ZONE DESCRIPTIONS

SECURITY SYSTEM NOTES Installing/Service Company For Service Call SPECIAL CODES Master Code Duress Code 'Quick Arm' Digit 'Chime' Digit 'Entry-Guard' Digit AUXILIARY ARM / DISARM CODES 02 12 22 03 13 23

More information

HILLS Series LED Code Pad User Manual

HILLS Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed Page 2 TABLE OF CONTENTS Code Pad Diagrams..2

More information

Using your LED Plus keypad

Using your LED Plus keypad System 238 System 2316 System 238i System 2316i Part Number 5-051-372-00 Rev B Thank you for purchasing this C&K alarm system Your system is one of the most powerful and advanced

More information

User s Information Guide R1A

HSC505-R Home Security Controller - User Manual Release R1a Pi HSC505 and Pi HSC505R Home Security Controller User s Information Guide R1A Page 1 QD Dynamics (Pty) Ltd reserves the right to make changes

More information

ICP-CC488 ICP-CC488 EN. Control Panel. Quick Reference Guide

ICP-CC488 EN Quick Reference Guide ICP-CC488 Control Panel ICP-CC488 Quick Reference Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security

More information

Using Your. Security System With Icon Keypad S5020, S5021, S5022

Using Your Security System With Icon Keypad S5020, S5021, S5022 Contents 1 Overview Your Security System.. 1 How Your Security System Works.. 2 Your System's Programming.. 3 Getting Used to Your System..

More information

GE Concord 4 Quick User Guide

GE Concord 4 Quick User Guide GE Concord 4 Quick User Guide Page 1 Before Calling Is the keypad beeping? Press *. This will silence the beeping and let you know where the trouble is. Is there a flashing

More information

SECURITY SYSTEM NOTES SPECIAL CODES. Security System Configuration

Installing / Service Company: SECURITY SYSTEM NOTES For Service Call: Master Code SPECIAL CODES Duress Code Security System Configuration Auxiliary Code(s) Quick Arm' Digit: 2 9 3 10 4 11 5 12 6 13 7 14

More information

SECURITY SYSTEM NOTES. Security System Configuration

Installing / Service Company: For Service Call: SECURITY SYSTEM NOTES Security System Configuration Master Code: Auxiliary Code(s) 2 3 4 5 6 'Quick Arm' Digit: Exit Delay Time Auxiliary Exit Delay Time

More information

ICP-CC488 ICP-CC488 EN. Control Panel. User s Guide

ICP-CC488 EN User s Guide ICP-CC488 Control Panel ICP-CC488 User's Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems, Inc. ( Bosch

More information

SECTION 13850 DETECTION AND ALARM

SECTION 13850 DETECTION AND ALARM PART 1 GENERAL 1.01 SUMMARY A. Section Includes 1. Control Panel 2 Associated Equipment B. Products Installed But Not Supplied Under This Section 1. Section 16140 - Wiring

More information

SCORPION. micron security products

SCORPION 4120 6020 & 8020 USER INSTRUCTIONS Thank you for purchasing a Quality Micron Security Alarm Controller. Micron product is manufactured to exacting quality standards. We understand the importance

More information

HILLS Series LED Code Pad User Manual

HILLS Series LED Code Pad User Manual Not all features may be available on your system Check with your installer to find out which features are programmed Page 2 TABLE OF CONTENTS Code Pad Diagrams..2

More information

Solution 880 Operators Manual ISSUE 1.10

Solution 880 Operators Manual ISSUE 1.10 Solution 880 Operators Manual Copyright 2001 by, SYDNEY, AUSTRALIA Document Part Number MA408O DOCUMENT ISSUE 1.10 Printed 25 May 2001 This documentation is provided

More information

NX-591NE-GSM NetworX GSM 3G HSPA+ Module Installation Sheet

NX-591NE-GSM NetworX GSM 3G HSPA+ Module Installation Sheet The NX-591NE-GSM is a microprocessor-controlled GSM interface module used to connect the NetworX series of control panels to GSM cellular networks

More information

Users Guide to Keypad Functions

Users Guide to Keypad Functions MANUAL NO. 700-175-01J ISSUED JAN 2002 VERSION 1.41 Summary of Operation A rm/ disarm [#] + [USER CODE] Quick Quick Quick Panic Fire Medical Away Arm Stay Arm Stay Arm &

More information

INSTALLATION MANUAL PC2525. Version 1.1

INSTALLATION MANUAL PC2525 Version 1.1 TABLE OF CONTENTS FEATURES 1 SPECIFICATIONS 1 INSTALLATION 2 Mounting the Panel.. 2 Mounting the Keypad.. 2 Auxiliary Power Connection.. 2 Bell/Siren Connection..

More information

System Introduction S E C T I O N 1

System Introduction S E C T I O N 1 1.1 Specifications Flexible Zone Configuration Six fully programmable zones; system expandable to eight zones using keypad zone inputs and wireless zones 38 access codes:

More information

Enhanced. Commercial Burglary Partitioned Security System with Scheduling. User Guide. K4970-1V3 4/09 Rev. B FA560 3 STAY 2 AWAY 1 OFF 5 TEST 9 CHIME

BS/ESC N/Y SHIFT ARMED READY A D S SPACE R B E T C F X ENTER ARMED READY MAX INSTANT READY R BYPASS FA1660C Enhanced Commercial Burglary Partitioned Security System with Scheduling 4 1 5 FA560 6 7 8 9

More information

Elite 8D/Lite Version 8 Zone Controller. Arrowhead Alarm Products Ltd. Operating Guide. Proudly Designed and Manufactured in New Zealand

Elite 8D/Lite Version 8 Zone Controller 8 Arrowhead Alarm Products Ltd Operating Guide 1 Proudly Designed and Manufactured in New Zealand 2 CONTENTS Page No. INTRODUCTION 4 About your Alarm 4 OPERATING

More information

FIRST ALERT INSTRUCTION MANUAL FOR FA 270 KEYPADS SECURITY SYSTEM

FIRST ALERT INSTRUCTION MANUAL FOR FA 270 KEYPADS SECURITY SYSTEM Page 0 Table of Contents Introduction 1 System Basics. 1 Burglary Protection. 1 Fire Protection. 1 Security Codes. 1 Zones and Partitions

More information

SECURITY SYSTEM NOTES SPECIAL CODES ENTRY / EXIT DELAY TIMES ARM / DISARM CODES

SECURITY SYSTEM NOTES Installing/Service Company For Service Call SPECIAL CODES 'Chime' Digit 1 'Partial Arm' Digit 2 'Quick Arm' Digit 3 ENTRY / EXIT DELAY TIMES Exit Delay Time Entry Delay Time Secondary

More information

VISTA-50P VISTA-50PUL

S e c u r i t y S y s t e m User's Manual VISTA-50P VISTA-50PUL N5943-6 7/95 TABLE OF CONTENTS SYSTEM OVERVIEW.. 3 A Partitioned System.. 3 Zones.. 3 Fire Protection.. 4 Burglary Protection.. 4 Alarms..

More information

CONTENTS 4. HOW TO UNSET THE PANEL..7

Pi-8 USER MANUAL CONTENTS 1. THE KEYPAD AND ITS OPERATION..3 1.1 DESCRIPTION OF THE KEYPAD LEDS.. 3 1.1.1 READY LED (RED)..3 1.1.2 TAMPER LED (RED)..3 1.1.3 POWER LED (GREEN)..3 1.1.4 CIRCUIT LEDs

More information

MONITOR ISM / AFx Multi-Tenant Security System User Guide V1.3

MONITOR ISM / AFx Multi-Tenant Security System User Guide V.3 Multi-Tenant Security System User Guide Welcome New Users! There are two types of suite security keypads. Follow the instructions in the proceeding

More information

First Alert FA145 Installer Notes M. Leuck

First Alert FA145 Installer Notes M. Leuck 1. Programming can only be done by 6139 Alpha keypads, standard 6128 keypad cannot be used to program zones 2. Program new Master Code in section *20 (old version)

More information

User's Manual. For use with ProSYS 16, ProSYS 40, and ProSYS 128

User's Manual For use with ProSYS 16, ProSYS 40, and ProSYS 128 Important Notice This manual is delivered subject to the following conditions and restrictions: This manual contains proprietary information

More information

Accenta/Optima. User Guide. Servicing Organisation (Installer) name: Telephone Number: Date of Installation: Account Number: Honeywell Security

Accenta/Optima User Guide ZONE 1 2 3 4 5 6 7 8 9 Chime Omit Prog PA 0 1 2 3 4 5 6 7 8 9 CHIME OMIT RESET PROG SET Accenta + TA PA DAY POWER PA! ' # $ % & 0 1 2 3 5 6 7 8 Chime Omit Reset Prog 4 9 Set PA

More information

Cerber C612 12-Zone and 2-Partition Burglary Control Panel For your home and office

Cerber C612 12-Zone and 2-Partition Burglary Control Panel For your home and office Doc 10905/ 09.2005/ version 2.0 User s Guide 1. INTRODUCTION..4 General Features..4 User Codes..4 Installer Codes..5

More information

Using Your. Security System. With LED Keypad S5030, S5031, S5032

Using Your Security System With LED Keypad S5030, S5031, S5032 Contents 1 Overview Your Security System.. 1 How Your Security System Works.. 2 Your System's Programming.. 3 Getting Used to Your System..

More information

SCORPION Z16040C Alarm Controller User Instructions

SCORPION Z16040C Alarm Controller User Instructions Thank you for choosing to purchase this micron security alarm controller. Micron product is manufactured to exacting quality standards. We understand

More information

8VHU V*XLGH 6HFXULW6VWHPV (QWUHSUHQHXU(1 6HFXULW0DQDJHU(1. Meets ADT Security Services Triple Standards Requirements:

6DIHZDWFK3UR Š (1 (QWUHSUHQHXU(1 6HFXULW0DQDJHU(1 6HFXULW6VWHPV 8VHU V*XLGH Meets ADT Security Services Triple Standards Requirements: C US LISTED Standards for Security and Fire Standard for False

More information

VISTA-100. Commercial Fire and Burglary 8VHU*XLGH. Partitioned Security System. N6020-2 Rev B 4/99 FIRE FIRE PULL

VISTA-100 Commercial Fire and Burglary Partitioned Security System 8VHU*XLGH FIRE FIRE * PULL N6020-2 Rev B 4/99 TABLE OF CONTENTS SYSTEM OVERVIEW.. 3 A Partitioned System.. 3 Zones.. 3 Fire Protection..

More information

tattletale User Guide Consumer unit version 2.48 1 P a g e

tattletale User Guide Consumer unit version 2.48 1 P a g e Contents Basic 1.. 4 Base Unit Features.. 4 Initial Setup.. 4 Arming.. 5 Disarming.. 5 Quiet Button.. 5 Settings.. 5 Settings 2.. 6 Quick

More information

TABLE OF CONTENTS FEATURES

TABLE OF CONTENTS FEATURES 2 Keypad Programmable.. 2 EEPROM Memory.. 2 Static/Lightning Protection.. 2 Supervision.. 2 Operation.. 2 SPECIFICATIONS 2 PC1550 Control Panel.. 2 PC1500RK Keypad.. 2

More information

Reference & Installation Manual

& Versions 4.4 (728ULT) & 4.1 (738ULT) 728ULT 738ULT Reference & Installation Manual Table of Contents Introduction.. 1 About This Manual.. 1 New Features.. 1 Main Features.. 1 Specifications.. 1

More information

616, 626, 636 & 646 Keypads

616, 626, 636 & 646 Keypads User s Manual TABLE OF CONTENTS 1.0 BASIC OPERATION..2 2.0 ACCESS CODES..4 3.0 ARMING & DISARMING..6 4.0 PANIC ZONES..13 5.0 KEY ACCESS PROGRAMMING.14 6.0 ADDITIONAL FEATURES..15

More information

Destiny 4100. Destiny 4100. Owners Manual

Destiny 4100 Destiny 4100 Owners Manual TABLE OF CONTENTS INTRODUCTION Control Panel..3 Detection Devices..3 Telephone Keypads..3 GLOSSARY.. 4-5 LOCAL PHONE ACCESS Using Your Telephones As Keypads..6

More information

PowerWave-8. Users Operating and Programming Guide Version 8.64. 8 zone Control panel Communicator

ELECTRONIC ENGINEERING LTD. PowerWave-8 8 zone Control panel Communicator Users Operating and Programming Guide Version 8.64 P/N 7101261 Rev. C N.A July 2002 2 Contents Introduction..5 Meet the Crow Alarm

More information

First Alert FA140C/142C Installer Notes M. Leuck

First Alert FA140C/142C Installer Notes M. Leuck 1. Programming can only be done by 6139 Alpha keypads, standard 6128 keypad cannot be used to program zones 2. Program new Master Code in section *20 (old

More information

HUNTER-PRO 32 Ver. 3.8 Intruder Alarm System RXN-9/416 User Guide

HUNTER-PRO 32 Ver. 3.8 Intruder Alarm System RXN-9/416 User Guide PIMA Electronic Systems Ltd. 5 Hatzoref Street, Holon 58856, Israel +972-3-5587722 +972-3-5500442 support@pima-alarms.com http://www.pima-alarms.com

More information

FA701 Series. User s Guide. K6249-2V2 5/09 Rev. A

FA701 Series TouchCenter Keypads User s Guide K6249-2V2 5/09 Rev. A Table of Contents ABOUT THE TOUCHCENTER.. 5 Introduction.. 5 2 The TouchCenter Interface.. 5 Navigating through the TouchCenter..

More information

ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems

ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems User Guide K5309-1V4 10/04 Rev. A IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should

More information

ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems

ADEMCO VISTA SERIES VISTA-20P / VISTA-20PSIA VISTA-15P / VISTA-15PSIA Security Systems User Guide K5309-1V7 3/15 Rev A IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should

More information

728 SERIES REFERENCE & INSTALLATION MANUAL 728+ VERSION 3.2. 728 series

728 SERIES 728+ VERSION 3.2 728 series REFERENCE & INSTALLATION MANUAL TABLE OF CONTENTS INTRODUCTION.. 2 About This Manual.. 2 Features.. 2 Specifications.. 3 Accessories and Keypads.. 3 About Paradox..

More information

Lynx Plus Series Security System

Lynx Plus Series Security System User Guide ARMED READY ESCAPE ADD OFF AWAY RECORD LIGHTS ON 1 2 3 VOLUME TEST PLAY 4 5 6 BYPASS 7 8 9 STAY DELETE AUX SELECT LIGHTS OFF 0 CODE CHIME STATUS NO DELAY FUNCTION

More information

Security System. User Guide for the LED Command Center

Security System User Guide for the LED Command Center MY SECURITY COMPANY IS: CALL BEFORE TEST: THIS SECURITY SYSTEM IS CONNECTED TO TELEPHONE NUMBER: THE SECURITY CONTROL PANEL IS CONNECTED TO THE PHONE

More information

6HFXULW6VWHPV 8VHU V*XLGH K5309-1V1 8/01

9,67$39,67$3&1 9,67$39,67$3&1 6HFXULW6VWHPV 8VHU V*XLGH K5309-1V1 8/01 1 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry

More information

SPECIAL CONTROL BUTTON FUNCTIONS

Operating Guide 1 2 3 CONTENTS Page No. OPERATING YOUR ALARM 5 General Information 5 Arming the Alarm 5 Disarming the Alarm 6 Arming in Stay Mode 7 Disarming Stay Mode 8 Bypassing Zones 8 Manual Panic,

More information

Simon XTi Quick Operation Guide

Simon XTi Quick Operation Guide This is the Quick Operation Guide for the Simon XTi system (models 600-1054-95R-12 & 600-1054-95R-12-CN). The Simon XTi provides a graphical user interface for programming

More information

Security System. User's Guide. Keypad

Security System EN User's Guide Keypad Security System User's Guide This system includes a telephone line seizure feature. The system can be programmed to communicate with a central monitoring station

More information

CONTENTS QUICK SETUP & INSTALLATION USER MANUAL. SUPA8 Quick Setup & User Manual

SUPA8 Quick Setup & User Manual QUICK SETUP & INSTALLATION CONTENTS FACTORY DEFAULTS.. 1 INSTALLATION OF THE SECURITY SYSTEM.. 2 COMMISSIONING THE DIALLER PANEL.. 5 ZONE INPUT CONNECTIONS.. 7 PANEL

More information

2 4PI175 issue 1_6/01. How to unset system in alarm. Programs 1, 2 and 3. Access codes. How to operate Personal Attack

Access codes Contents Unset system indications - - - - - - - - - - - System indication - - - - - - - - - - - - Access codes - - - - - - - - - - - - - - - - How to operate Personal - - - - - - How to unset

More information

D1260/D1260B. Keypad. National Security Systems Inc (800)457-1999. Owner's Manual

D1260/D1260B EN Owner's Manual Keypad National Security Systems Inc (800)457-1999 D1260/D1260B Owner's Manual This system includes a telephone line seizure feature. The system may be programmed to communicate

More information

SECURITY SYSTEM NOTES AREA LISTINGS SPECIAL CODES ENTRY / EXIT DELAY TIMES ARM / DISARM CODES ZONE DESCRIPTIONS

SECURITY SYSTEM NOTES Installing/Service Company For Service Call Area 1 Area 2 Area 3 AREA LISTINGS SPECIAL CODES 'Quick Arm' Digit 'Partial Arm' Digit 'Chime' Digit ENTRY / EXIT DELAY TIMES Exit Delay

More information

Ademco Vista-20P/First Alert FA-168C Basic Commands

Zones 64 total Ademco Vista-20P/First Alert FA-168C Basic Commands Wireless Yes, Zones 09 to 48 + 16 Keyfob Zones (Zones 49 to 64) Batteries Downloadable Partitions 2 12 volt Rechargable inside main Panel,

More information

GC2 Panel User Guide

GC2 Panel User Guide ENGLISH (International) WIRELESS SECURITY SYSTEM WARNING: OWNER S I NSTRUCTION NOTICE Not to be removed by anyone except occupant THIS PAGE INTENTIONALLY LEFT BLANK CONTENTS System

More information

Zone Assignment. PC5010 Zone 1-16 Assignment. System Parti- Zone Label Zone Zone Attributes Serial Number. Zone tion Type (Wireless)

Zone Assignment PC5010 Zone 1-16 Assignment System Parti- Zone Label Zone Zone Attributes Serial Number Zone tion Type (Wireless) Wireless Tx Del. Swing. 1 2 Force Bypass Chime Steady/Pulsed Audible/Silent

More information

DESTINY OWNER S MANUAL

DESTINY OWNER S MANUAL DESTINY You have made a wise decision to protect your family and property with the DESTINY Security System. The DESTINY has been designed to provide you with a maximum level of security

More information

Contact ID as of 2/2/2015

Contact ID as of 2/2/2015 100 Medical Zone A non-specific medical exists 101 Personal Emergency Zone Emergency Assistance request 102 Fail to report in Zone A user has failed to activate a monitoring device

More information

LCD and 16-Zone LED Keypads. User s Manual

LCD and 16-Zone LED Keypads 1689 1641 16-Zone LED Keypad LCD Keypad User s Manual TABLE OF CONTENTS 1.0 INTRODUCTION..3 2.0 BASIC OPERATION..4 2.1 Keypad Indicator Lights.. 4 2.2 Visual Feedback..

More information

Intruder alarm XR2/ system Operating XR2+ Instructions ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7

ZONE ZONE 2 ZONE ZONE ZONE 5 ZONE 6 ZONE 7 ZONE Power PA XR2/ XR2+ Intruder alarm system Operating Instructions ZONE ZONE 2 ZONE ZONE ZONE 5 ZONE 6 ZONE 7 ZONE 0 2 5 6 7 9 Omit Prog Remote LED keypad 0

More information

astec Integrated Alarm System USER GUIDE

astec Integrated Alarm System USER GUIDE 020008599 CONTENTS Full Set, Part Set and Disarm 3 Instant Full Set 3 Part Set with exit time 4 Bell Test 4 Bypassing zones 4 Switch Lights on/off 4 Bypass (24

More information

EVO48 EVO192. User Guide

EVO48 EVO192 User Guide We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us your comments. Table of Contents

More information

Content. 1. Introduction to the IDS Features Installation and Wiring End-of-Line Resistors/Tamper per Zone..

1 2 Content 1. Introduction to the IDS 805.. 7 1.1 Features..7 2. Installation and Wiring..8 3. End-of-Line Resistors/Tamper per Zone..9 4. Connecting the Telephone Communicator..10 5. Programmable

More information

D24 ALARM CONTROL PANEL USER S MANUAL REVISION 1.1 A$12.00 INC GST

D24 ALARM CONTROL PANEL USER S MANUAL REVISION 1.1 A$12.00 INC GST Ness Security Products Pty Ltd Quality Endorsed Company ISO9001 LIC.No. QEC2074 NSW Head Office only WWW.NESS.COM.AU Australia s largest

More information

System Manager s Manual

LCD Keypad DGP2-641B / DGP2-641RB DGP2-641 / DGP2-641R System Manager s Manual Also includes Operating Instructions Table of Contents Introduction.. 1 Legend.. 1 Basic Operation.. 1 Auditory Feedback

Installation Guide

More information

XP-600 Programming Instructions

Hexadecimal Data Entry To Enter a hexadecimal digit enter the following A= A1 D= A4 B= A2 E= A5 C= A3 F= A6 XP-600 Programming Instructions Note These Programming Instructions are intended to be used in

More information

VR8. User Guide Intruder Alarm System

VR8 EN User Guide Intruder Alarm System VR8 User Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch ). How to install wiixplorer. All rights

More information

1728EX, 1728, 1738EX AND 1738 SYSTEM PROGRAMMING GUIDE Software Version 2.1

1728EX, 1728, 1738EX AND 1738 SYSTEM PROGRAMMING GUIDE Software Version 2.1 DEFAULT INSTALLER CODE 000000 (see section [281] on page 18) DEFAULT SYSTEM MASTER CODE 123456 (see section [301] on page 18)

More information

HARDWIRED CONTROL PANELS

USER GUIDE 9651 HARDWIRED CONTROL PANELS Contents 1. Introduction..3 The Alarm System..3 The Keypad..3 About This Guide..5 2. Everyday Operation..6 How Do I Know if the System is Working?..6 Setting

More information

642 LCD Keypad User Manual

642 LCD Keypad User Manual TABLE OF CONTENTS Introduction..3 Legend.. 3 Basic Operation..5 Keypad Indicator Lights.. 5 Visual Feedback.. 5 Auditory Feedback.. 6 Info List.. 7 Access Codes..8 User

More information

LYNX Touch Security System

LYNX Touch Security System User Guide 1:35 2 PM October 26, 2011 72 Mostly Sunny 68 F F Feels Like 71 Security Messages Automation 5-Day Forecast News Traffic 800-10615 1/12 Rev. A LYNX Touch L5100 Series

More information

Solution-8 Control Panel

Solution-8 Control Panel Issue 3c September 1994 Copyright 1994-1995 All rights reserv (MA 800 O) Important Note As there are many different types of consoles available for use with this control panel,

More information

LYNX Touch Security System

LYNX Touch Security System User Guide 800-10615V1 12/12 Rev. A LYNX Touch L5100 Series Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell for use with

More information

NESS D16. 16 Zone Control Panel and Dialler OWNER S MANUAL

NESS D16 16 Zone Control Panel and Dialler OWNER S MANUAL REVISION 2, JULY 2001 Ness Security Products Pty Ltd Quality Endorsed Company ISO9001 LIC.No. QEC2074 NSW Head Office only WWW.NESS.COM.AU Australia

More information

THANK YOU FOR VOTING TEXECOM MASTER USER MANUAL. Security Control Panels with Integrated Communicator. Issue 6

THANK YOU FOR VOTING TEXECOM MASTER USER MANUAL Security Control Panels with Integrated Communicator Issue Contents Premier 4// Master User Manual Contents. About the System.. Introduction.. About this

H57h-am2 v1.0 manual. There is often some processing time before a refund is posted.

Bosch Vr8 Installation Manual English

More information